Electrician in Childers, QLD

Where we work in Childers

Childers is an inland cane town with a historic main street, Churchill Street, lined with older buildings. There is no sea breeze here, and the heat in summer sits on the town. The work splits between homes on the side streets and shops and small businesses along and near the main street. A lot of it is about older buildings that were wired and built for a lighter load than people now put on them, so we take our time to see what is there.

Home blocks are a decent size, often with a shed or a few fruit trees in the back yard, and side gates are common. Shops along the main street may share a laneway at the back for access, and a ladder or a delivery may need to come through a rear door. Meter boxes sit on a side wall or at the rear of a shopfront, and the switchboard can be inside the shop, in a back room or up a set of stairs.

Older homes are timber and tin, with high ceilings, wide verandahs and sometimes a roof space that is very hot in summer. The wiring behind the walls can be decades old, and a switchboard may still hold ceramic fuses. Shopfronts are often brick or timber with iron roofs and a few extensions. Storms and hail on a tin roof can loosen fixings, so we check them, and fibro sheeting is left alone until we know what it is.

What we do here most

What Childers buildings keep needing

The pattern here is an old building in hot cane country being asked to carry modern power and cooling.

Electrical Wiring

Rewiring a timber and tin house room by room

A timber house with high ceilings is often wired through a roof space that is full of dust and heat. We open the switchboard first, then trace the cable through the roof and under the floor, and work out what can stay. We talk through what to replace and which rooms to do first, so you can stay in the house while it happens.

Split System Air Conditioning

One wall unit for a tall, hot lounge

A tall room under an iron roof holds the day's heat well into the evening. We look at where the indoor unit can hang for the best air flow, and how the pipe will cross a timber wall without spoiling it. The outdoor unit goes on the ground or a bracket, and we check the circuit in the board.

Solar Panel Installation

Panels on an old iron roof after hail

Before panels go on, an old iron roof needs checking. We walk it carefully, look at the sheeting, the screws and the roof timbers, and see whether anything has lifted or rusted. We note which sections face the sun for the longest hours. If the roof needs work first, we say so. The network application goes to Ergon Energy Network.

Electrical Maintenance

Checking the board and lights in an older shopfront

A shop on the main street may have a board that has been added to for years, with new circuits tacked on beside old ones. We open it and look at the main switch, the loose ways and the earthing, then test the safety switches and check the lighting and power points in the shop. We tell you what needs fixing first.

If it is urgent

If the power drops out in your Childers house or shop

  1. 1Look at the switchboard, find any safety switch or fuse that has dropped or blown, and push the switch up once.
  2. 2Leave a switch that trips again alone, keep clear of any warm or scorched power point, and do not cut into old wall sheeting.
  3. 3When you ring 0741 536 493, tell us whether it is a house or a shop, the street, and whether the board has fuses or switches.
Call 0741 536 493

Common questions

Frequently Asked Questions

What work do you do?

We do electrical, solar and air conditioning work. That covers Solar Panel Installation, Solar System Design, Solar Inverter Installation, Solar Battery Storage, Solar Battery Installation, Air Conditioning Installation, Split System Air Conditioning, Electrical Wiring and Electrical Maintenance. Each one has its own page on this site.

Which places do you work in?

We work in Bundaberg, Bundaberg Central, Walkervale, Svensson Heights, Woodgate, Kepnock, Moore Park, Bargara, Childers, Norville, Gin Gin and Avondale. If your property is somewhere else nearby, ring and ask, because the list is where we name our work rather than a hard boundary.

Do you work on both homes and businesses?

Yes. The work is much the same in principle, but a shop or an office usually has a bigger switchboard and more circuits to look at. Tell us which kind of property it is when you ring and we will plan the visit around that.

Can you come and look at the property before I decide?

Yes. We can visit to see the switchboard, the meter box, the roof or the wall where the new equipment would go, and talk through the options with you. Visits are booked by phone or through the form on the contact page.

Can you design a solar system around how my household uses power?

Yes, that is what Solar System Design is for. We look at the roof, the direction it faces, any shade, the switchboard and the meter, and talk with you about when the household uses most of its power. The layout is worked out from those things rather than from a standard package.

Can I add a battery to the solar system I already have?

In most cases, yes. We start by looking at the existing inverter and how the system is wired, because that decides which type of battery can be fitted and where it connects. Once that is clear, we talk through the options and where the battery would sit.

Will a battery keep my house running in a blackout?

It depends on how the battery and inverter are wired, because not every setup runs the house when the grid is off. Some are set up to feed only a few circuits, such as the fridge and lights, while others cover more. We explain which circuits would stay on before anything is fitted.

Does a solar system need approval before it is switched on?

Grid connected solar in Queensland needs an application to the local network, which around Bundaberg is Ergon Energy Network. It is dealt with as part of the job, and the system is switched on only once that is sorted out. We explain where yours is up to when we hand it over.

What is the difference between a split system and a ducted system?

A split system is one indoor unit on a wall, joined by pipework and cable to an outdoor unit, and it cools the room it sits in. A ducted system has one outdoor unit and ducts running through the roof space to vents in several rooms. We can talk through which suits your house after seeing the layout and the roof space.

Where do the indoor and outdoor units of an air conditioner go?

The indoor unit goes high on a wall with room to blow across the space. The outdoor unit sits on a bracket or a slab outside, as close as is sensible, and needs clear space around it so air can move. We check both positions, and the run of pipework between them, before any work starts.

Will my switchboard need work to take a new air conditioner or battery?

Sometimes, and sometimes not. We open the switchboard first and look at the main switch, the spare ways and the earthing, then tell you whether the new equipment can connect as it is. If the board needs work, we say so before the job starts.

What does electrical maintenance involve?

It starts with looking at what is already there: the switchboard, the switches, powerpoints and light fittings, and any equipment you are worried about. We test what we can reach and tell you what we find. If something needs replacing, we talk it through with you first.

Local, and on the phone

Tell us about your Childers building

Tell us roughly how old the building is and what work you have in mind. That decides what we bring and how we plan the visit.

0741 536 493

24 hours a day, 7 days a week

Not urgent? Send us the job instead